
Klipsch Reference Theater Pack User Manual
By • Last UpdatedHere we Provide a Klipsch Reference Theater pack User Manual. This user guide of Reference theatre pack helps you to know How to set up Klipsch Reference theater pack and also you got aware about settings in this Home theatre.
Klipsch Reference Theater Pack User Manual

Specifications
SATELLITE & CENTER CHANNEL | |
---|---|
Frequency Response | 110Hz – 23kHz +/– 3dB |
Nominal Impedance | 8 ohms compatible |
Sensitivity | Satellite: 91dB @ 2.83 volts / 1 meter Center: 94dB @ 2.83 volts / 1 meter |
Power Handling | Satellite: 50 watts (200 watts peak) Center: 75 watts (300 watts peak) |
High Frequency Driver | Satellite & Center: 3/4” (1.9 cm) aluminum diaphragm compression driver mated to 90° x 90° Tractrix® horn |
Low Frequency Driver | Satellite: 3.5” (8.9 cm) copper IMG woofer Center: Dual 3.5” (8.9 cm) copper IMG woofer |
Dimensions | Satellite: 7.75” H (19.7cm) x 4.38” W (11.1cm) x 5.37” D (13.7cm) Center: 4.38” H (11.1cm) x 10.75” W (27.3cm) x 5.37”D (13.7cm) |
Weight | Satellite: 3 Ibs (1.4kg) Center: 5 Ibs (2.3kg) |
Mounting | Satellite: Keyhole and 1/4” x 20 threaded insert Center: Dual Keyhole with dual 1/4” x 20 threaded insert |
Speaker Wire | 14–18 gauge compatible |
SUBWOOFER | |
---|---|
Frequency Response | 38Hz – 120Hz +/– 3dB |
Amplifier Power | 50 watts / 150 watts peak |
Maximum Acoustic Output | 108 dB |
Inputs | 2.4 GHz CD-quality wireless & Line level / LFE RCA jacks |
Enclosure Material | MDF |
Enclosure Type | Bass Reflex via down-firing 8” woofer and port |
Dimensions | 13.25” H (33.7cm) x 11.75” W (29.9cm) x 11.75” D (29.9cm) |
Finish | Brushed Black Polymer Veneer |
Weight | 15.0 Ibs (6.8kg) |
How to Set up Klipsch Reference theater pack
Here we Provide a How to Set up Klipsch Reference Theater Pack easily Firstly we have to know about how to mount Klipsch reference theater pack wall (speakers Wall Mounting).



Speakers Placement in Listenning Area
Follow this for Set up Klipsch Reference theater pack


Subwoofer
CAUTION: Ensure that the subwoofer is unplugged from the AC wall outlet before making any connections.
In the absence of a subwoofer output on your receiver, as an alternative hookup, you can connect Left and Right channel Pre-Amp Outputs from your receiver (if provided) to th Left/LFE and Right input on the subwoofer
POWER LED
Located on the front baffle, this LED indicates the operating status of the built-in amplifier. The LED will light green when the amplifier is on and receiving a signal. If the LED is dark and not lit, the amplifier is off. For more information on the controls mentioned in this manual and on bass management, see your dealer or visit www.klipsch.com
POWER SWITCH
When this switch is in the “ON/AUTO” position, the subwoofer will automatically turn “on” when it senses a signal. It will automatically go into “standby mode” after 15-20 minutes with no signal. When this switch is in the “OFF” position, the subwoofer will remain “off” until the switch is manually turned back to the “ON/AUTO” position
GAIN
If your subwoofer is connected to a Subwoofer Output of a surround receiver, first set the subwoofer volume level control in the receiver to the “half way” or “0 dB” position. Then increase the volume (or gain) of the subwoofer up until the subwoofer’s volume level matches the output of your main speakers. After this setup is completed, the volume control on your system’s main amplifier or pre-amplifier will be the volume control for both your subwoofer and speakers together. If your subwoofer is connected to the L/R Pre-Amp Outputs of a receiver there will be no subwoofer volume in that receiver to set before setting the subwoofer’s gain control.
LOWPASS (Hz)
The crossover point chosen determines where low bass frequencies are “handed off” from the speakers to the subwoofer. If setting the crossover point in the receiver, turn the Lowpass Filter knob on the subwoofer to the farthest point right (160Hz). Set the crossover point based on the size of the main left/right speakers you are using in the system. As a general rule, for larger, floorstanding speakers, set the crossover point between 50Hz-90Hz. If using small bookshelf or “satellite” speakers for the mains, set the crossover point between 90Hz-150Hz. The smaller the speaker, the higher the setting until the bass frequencies blend well between the speakers and your subwoofer once your system is completely hooked up. If your receiver does not have a crossover point setting, set the Lowpass Filter on the subwoofer instead within the same recommended settings (see receiver manual for additional speaker setup info)
PHASE
This control is used to acoustically match the subwoofer’s output to your main speakers. Select the position either 0˚ or 180˚ in which your subwoofer has more output at the listening position.




Important Safety Instructions.
- READ these instructions.
- KEEP these instructions.
- HEED all warnings.
- FOLLOW all instructions.
- DO NOT use this apparatus near water.
- CLEAN ONLY with dry cloth.
- DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- ONLY USE attachments/accessories specified by the manufacturer.
- USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
- DO NOT expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the apparatus.
Care and Cleaning
Your speakers have a durable finish that should only require dry dusting or cleaning with a dry cloth. Avoid the use of abrasive or solvent-based cleaners and harsh detergents. The brush attachment of your vacuum should remove any dust from your speaker grilles.
Conventional Connection
Using 18-gauge or larger speaker wire, connect the RED “positive” (+) terminal of the LEFT speaker to the RED “positive” (+) terminal of your amplifier’s LEFT channel. Connect the BLACK “negative” (-) terminal of the LEFT speaker to the BLACK “negative” (-) terminal of your amplifier’s LEFT channel. Repeat this proce- dure for connecting all remaining speakers to the appropriate amplifier channels. Make sure no bare wires from any of the connections touch any other bare wires or terminals as this could cause a short and damage your equipment.
Amplifier Requirements
Klipsch speakers are highly efficient and will work well with a wide variety of am- plifiers. Due to the high output levels, Klipsch speakers are capable of reproducing, exercise caution with the volume control. Excessive volume over long periods of time can permanently damage your hearing. Overdriving your amplifier could also damage your speakers. Check with your dealer to make sure your particular amplifier is best suited to your application. We want you to listen for a lifetime.
Conclusion
This Klipsch Reference Theater pack user Manual helps to know the Settings of this home theatre and also helps in How to Set Up Klipsch Reference Theater Pack. we Hope this Klipsch Reference Theater Pack User Guide Resolves all Problems related to this Home theater, If your Issues are not Resolved you have to Visit the Service Center or Contact Customer Care of Klipsch.
Thank You! | Team TWSOne.com
Read Also
- Best Boat Airdopes In India
- Best Multi Channel Home Theatre System
- Best Sony Wireless Subwoofer
- Klipsch Reference Theater Pack Short Review
Credit:- Klipsch